请求将SW799更名为Fine3399

[r1172464137]

Fine3399是rumu3f设计的一个多用途嵌入式主板，采用bozztek的SW799系列核心板，处理器为RK3399。

Fine3399资料网站: https://gitee.com/opengisbook/Fine3399-Official

长风大佬的dts提交(其中有SPI Flash和屏幕的定义，但被注释了): cm9vdA/build-linux@ab3e4f5

[ophub]

https://github.com/ophub/amlogic-s9xxx-armbian/releases/download/Armbian_jammy_save_2023.10/Armbian_23.11.0_rockchip_fine3399_jammy_6.1.58_server_2023.10.17.img.gz

你下载这个镜像测试下，使用的u-boot和dts文件都是来自 https://github.com/cm9vdA/build-linux 大佬的仓库。测试好了再把sw799合并到一个共用。

[r1172464137]

不行

[r1172464137]

U-Boot TPL 2022.07 (Oct 18 2023 - 10:03:11)
Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2022.07 (Oct 18 2023 - 10:03:11 +0800)
Trying to boot from MMC2


U-Boot 2022.07 (Oct 18 2023 - 10:03:11 +0800)

SoC: Rockchip rk3399
Reset cause: POR
Model: Fine3399
DRAM:  3.9 GiB
PMIC:  RK808
Core:  278 devices, 29 uclasses, devicetree: separate
MMC:   mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Fine3399
Net:
Error: ethernet@fe300000 address not set.
No ethernet found.

Hit any key to stop autoboot:  0
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
3252 bytes read in 11 ms (288.1 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 0
265 bytes read in 9 ms (28.3 KiB/s)
16866283 bytes read in 1612 ms (10 MiB/s)
33923584 bytes read in 3225 ms (10 MiB/s)
78941 bytes read in 25 ms (3 MiB/s)
Failed to load '/dtb/rockchip/overlay/rk3399-fixup.scr'
Unknown command 'kaslrseed' - try 'help'
Moving Image from 0x2080000 to 0x2200000, end=4340000
## Loading init Ramdisk from Legacy Image at 06000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    16866219 Bytes = 16.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Ramdisk to f0efe000, end f1f13bab ... OK
   Loading Device Tree to 00000000f0e82000, end 00000000f0efdfff ... OK

Starting kernel ...

efi_free_pool: illegal free 0x00000000f0f16040
efi_free_pool: illegal free 0x00000000f0f13040
efi_free_pool: illegal free 0x00000000f0f11040
[    2.947628] Internal error: Oops: 0000000086000005 [#1] SMP
[    2.948138] Modules linked in:
[    2.948417] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G    B              6.1.58-ophub #1
[    2.949120] Hardware name: Fine3399 (DT)
[    2.949471] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    2.950089] pc : 0x0
[    2.950294] lr : rcu_core+0x1bc/0x500
[    2.950629] sp : ffffffc00a153ed0
[    2.950925] x29: ffffffc00a153ed0 x28: ffffffc00810faac x27: 0000000000000000
[    2.951565] x26: ffffff80f7f43f38 x25: ffffffc009e8d7c0 x24: 000000000000000a
[    2.952205] x23: 0000000000000003 x22: ffffffc00a153f40 x21: ffffff80006af000
[    2.952847] x20: ffffff80f7f43ec0 x19: 0000000000000004 x18: 000000000000017d
[    2.953488] x17: ffffffc0ee573000 x16: ffffffc00a150000 x15: 0000000000000000
[    2.954128] x14: ffffff80006af000 x13: 00000000000003ee x12: 0000000000000000
[    2.954768] x11: 0000000000000003 x10: ffffffc009d8eaa0 x9 : ffffff80f7f49318
[    2.955408] x8 : fffffffe00233e08 x7 : 0000000000000000 x6 : 0000000000000001
[    2.956050] x5 : ffffff80f7f49300 x4 : 0000000000000000 x3 : 0000000000000000
[    2.956722] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff8001cfe000
[    2.957397] Call trace:
[    2.957635]  0x0
[    2.957824]  rcu_core_si+0x10/0x20
[    2.958156]  _stext+0x10c/0x290
[    2.958466]  ____do_softirq+0x10/0x20
[    2.958823]  call_on_irq_stack+0x24/0x58
[    2.959204]  do_softirq_own_stack+0x1c/0x30
[    2.959605]  irq_exit_rcu+0x7c/0xa4
[    2.959945]  el1_interrupt+0x4c/0xb0
[    2.960294]  el1h_64_irq_handler+0x18/0x2c
[    2.960689]  el1h_64_irq+0x74/0x78
[    2.961019]  cpuidle_enter_state+0x138/0x2f0
[    2.961432]  cpuidle_enter+0x40/0x60
[    2.961780]  do_idle+0x1c8/0x240
[    2.962102]  cpu_startup_entry+0x38/0x40
[    2.962484]  secondary_start_kernel+0x144/0x184
[    2.962923]  __secondary_switched+0xb0/0xb4
[    2.963336] Code: bad PC value
[    2.963633] ---[ end trace 0000000000000000 ]---
[    2.964064] Kernel panic - not syncing: Oops: Fatal exception in interrupt
[    2.964691] SMP: stopping secondary CPUs
[    2.965201] Kernel Offset: disabled
[    2.965529] CPU features: 0x80000,20824084,0000421b
[    2.965984] Memory Limit: none
[    2.966281] ---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]---

[r1172464137]

U-Boot TPL 2022.07 (Oct 18 2023 - 10:03:11)
Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2022.07 (Oct 18 2023 - 10:03:11 +0800)
Trying to boot from MMC2


U-Boot 2022.07 (Oct 18 2023 - 10:03:11 +0800)

SoC: Rockchip rk3399
Reset cause: POR
Model: Fine3399
DRAM:  3.9 GiB
PMIC:  RK808
Core:  278 devices, 29 uclasses, devicetree: separate
MMC:   mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Fine3399
Net:
Error: ethernet@fe300000 address not set.
No ethernet found.

Hit any key to stop autoboot:  0
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
3252 bytes read in 11 ms (288.1 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 0
265 bytes read in 9 ms (28.3 KiB/s)
16866283 bytes read in 1612 ms (10 MiB/s)
33923584 bytes read in 3225 ms (10 MiB/s)
78941 bytes read in 25 ms (3 MiB/s)
Failed to load '/dtb/rockchip/overlay/rk3399-fixup.scr'
Unknown command 'kaslrseed' - try 'help'
Moving Image from 0x2080000 to 0x2200000, end=4340000
## Loading init Ramdisk from Legacy Image at 06000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    16866219 Bytes = 16.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Ramdisk to f0efe000, end f1f13bab ... OK
   Loading Device Tree to 00000000f0e82000, end 00000000f0efdfff ... OK

Starting kernel ...

efi_free_pool: illegal free 0x00000000f0f16040
efi_free_pool: illegal free 0x00000000f0f13040
efi_free_pool: illegal free 0x00000000f0f11040
[    2.947628] Internal error: Oops: 0000000086000005 [#1] SMP
[    2.948138] Modules linked in:
[    2.948417] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G    B              6.1.58-ophub #1
[    2.949120] Hardware name: Fine3399 (DT)
[    2.949471] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    2.950089] pc : 0x0
[    2.950294] lr : rcu_core+0x1bc/0x500
[    2.950629] sp : ffffffc00a153ed0
[    2.950925] x29: ffffffc00a153ed0 x28: ffffffc00810faac x27: 0000000000000000
[    2.951565] x26: ffffff80f7f43f38 x25: ffffffc009e8d7c0 x24: 000000000000000a
[    2.952205] x23: 0000000000000003 x22: ffffffc00a153f40 x21: ffffff80006af000
[    2.952847] x20: ffffff80f7f43ec0 x19: 0000000000000004 x18: 000000000000017d
[    2.953488] x17: ffffffc0ee573000 x16: ffffffc00a150000 x15: 0000000000000000
[    2.954128] x14: ffffff80006af000 x13: 00000000000003ee x12: 0000000000000000
[    2.954768] x11: 0000000000000003 x10: ffffffc009d8eaa0 x9 : ffffff80f7f49318
[    2.955408] x8 : fffffffe00233e08 x7 : 0000000000000000 x6 : 0000000000000001
[    2.956050] x5 : ffffff80f7f49300 x4 : 0000000000000000 x3 : 0000000000000000
[    2.956722] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff8001cfe000
[    2.957397] Call trace:
[    2.957635]  0x0
[    2.957824]  rcu_core_si+0x10/0x20
[    2.958156]  _stext+0x10c/0x290
[    2.958466]  ____do_softirq+0x10/0x20
[    2.958823]  call_on_irq_stack+0x24/0x58
[    2.959204]  do_softirq_own_stack+0x1c/0x30
[    2.959605]  irq_exit_rcu+0x7c/0xa4
[    2.959945]  el1_interrupt+0x4c/0xb0
[    2.960294]  el1h_64_irq_handler+0x18/0x2c
[    2.960689]  el1h_64_irq+0x74/0x78
[    2.961019]  cpuidle_enter_state+0x138/0x2f0
[    2.961432]  cpuidle_enter+0x40/0x60
[    2.961780]  do_idle+0x1c8/0x240
[    2.962102]  cpu_startup_entry+0x38/0x40
[    2.962484]  secondary_start_kernel+0x144/0x184
[    2.962923]  __secondary_switched+0xb0/0xb4
[    2.963336] Code: bad PC value
[    2.963633] ---[ end trace 0000000000000000 ]---
[    2.964064] Kernel panic - not syncing: Oops: Fatal exception in interrupt
[    2.964691] SMP: stopping secondary CPUs
[    2.965201] Kernel Offset: disabled
[    2.965529] CPU features: 0x80000,20824084,0000421b
[    2.965984] Memory Limit: none
[    2.966281] ---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]---

这是我用openwrt仓库打包固件的启动日志，我再试试armbian

[r1172464137]

armbian log

U-Boot TPL 2022.07 (Oct 18 2023 - 10:03:11)
Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2022.07 (Oct 18 2023 - 10:03:11 +0800)
Trying to boot from MMC2


U-Boot 2022.07 (Oct 18 2023 - 10:03:11 +0800)

SoC: Rockchip rk3399
Reset cause: POR
Model: Fine3399
DRAM:  3.9 GiB
PMIC:  RK808
Core:  278 devices, 29 uclasses, devicetree: separate
MMC:   mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Fine3399
Net:
Error: ethernet@fe300000 address not set.
No ethernet found.

Hit any key to stop autoboot:  0
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
3252 bytes read in 12 ms (264.6 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 0
269 bytes read in 8 ms (32.2 KiB/s)
16866283 bytes read in 1613 ms (10 MiB/s)
33923584 bytes read in 3225 ms (10 MiB/s)
78941 bytes read in 28 ms (2.7 MiB/s)
Failed to load '/dtb/rockchip/overlay/rk3399-fixup.scr'
Unknown command 'kaslrseed' - try 'help'
Moving Image from 0x2080000 to 0x2200000, end=4340000
## Loading init Ramdisk from Legacy Image at 06000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    16866219 Bytes = 16.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Ramdisk to f0efe000, end f1f13bab ... OK
   Loading Device Tree to 00000000f0e82000, end 00000000f0efdfff ... OK

Starting kernel ...

efi_free_pool: illegal free 0x00000000f0f16040
efi_free_pool: illegal free 0x00000000f0f13040
efi_free_pool: illegal free 0x00000000f0f11040

U-Boot TPL 2022.07 (Oct 18 2023 - 10:03:11)
Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2022.07 (Oct 18 2023 - 10:03:11 +0800)
Trying to boot from MMC2


U-Boot 2022.07 (Oct 18 2023 - 10:03:11 +0800)

SoC: Rockchip rk3399
Reset cause: POR
Model: Fine3399
DRAM:  3.9 GiB
PMIC:  RK808
Core:  278 devices, 29 uclasses, devicetree: separate
MMC:   mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Fine3399
Net:
Error: ethernet@fe300000 address not set.
No ethernet found.

Hit any key to stop autoboot:  0
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
3252 bytes read in 12 ms (264.6 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 0
269 bytes read in 8 ms (32.2 KiB/s)
16866283 bytes read in 1613 ms (10 MiB/s)
33923584 bytes read in 3225 ms (10 MiB/s)
78941 bytes read in 28 ms (2.7 MiB/s)
Failed to load '/dtb/rockchip/overlay/rk3399-fixup.scr'
Unknown command 'kaslrseed' - try 'help'
Moving Image from 0x2080000 to 0x2200000, end=4340000
## Loading init Ramdisk from Legacy Image at 06000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    16866219 Bytes = 16.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Ramdisk to f0efe000, end f1f13bab ... OK
   Loading Device Tree to 00000000f0e82000, end 00000000f0efdfff ... OK

Starting kernel ...

efi_free_pool: illegal free 0x00000000f0f16040
efi_free_pool: illegal free 0x00000000f0f13040
efi_free_pool: illegal free 0x00000000f0f11040

U-Boot TPL 2022.07 (Oct 18 2023 - 10:03:11)
Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2022.07 (Oct 18 2023 - 10:03:11 +0800)
Trying to boot from MMC2


U-Boot 2022.07 (Oct 18 2023 - 10:03:11 +0800)

SoC: Rockchip rk3399
Reset cause: POR
Model: Fine3399
DRAM:  3.9 GiB
PMIC:  RK808
Core:  278 devices, 29 uclasses, devicetree: separate
MMC:   mmc@fe320000: 1, mmc@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Fine3399
Net:
Error: ethernet@fe300000 address not set.
No ethernet found.

Hit any key to stop autoboot:  0
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
3252 bytes read in 12 ms (264.6 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 0
269 bytes read in 8 ms (32.2 KiB/s)
16866283 bytes read in 1613 ms (10 MiB/s)
33923584 bytes read in 3225 ms (10 MiB/s)
78941 bytes read in 28 ms (2.7 MiB/s)
Failed to load '/dtb/rockchip/overlay/rk3399-fixup.scr'
Unknown command 'kaslrseed' - try 'help'
Moving Image from 0x2080000 to 0x2200000, end=4340000
## Loading init Ramdisk from Legacy Image at 06000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    16866219 Bytes = 16.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Ramdisk to f0efe000, end f1f13bab ... OK
   Loading Device Tree to 00000000f0e82000, end 00000000f0efdfff ... OK

Starting kernel ...

efi_free_pool: illegal free 0x00000000f0f16040
efi_free_pool: illegal free 0x00000000f0f13040
efi_free_pool: illegal free 0x00000000f0f11040

[ophub]

内核恐慌，你使用sw799的固件可以正常启动？

[r1172464137]

可以

[ophub]

如果方便挂载img修改的话，你试试把rk3399-bozz-sw799.dtb 重命名成rk3399-fine3399.dtb，更换这个dtb试试？

[r1172464137]

我等会儿试下

[ophub]

rk3399-bozz-sw799.dtb 这个有dts源码没？我还说好容易有rk3399-fine3399.dts了，用这个呢

[r1172464137]

build-linux仓库有个bsp的dts，不知道是不是你说的那个

[ophub]

https://github.com/cm9vdA/build-linux/blob/master/boot/dts/rockchip/bsp/rk3399-fine3399.dts

我上面使用的是这个，你说的是哪个？

我回头删除了这个fine3399吧，把之前的sw799改名下，你找到dts了发给我下

[r1172464137]

https://github.com/cm9vdA/build-linux/blob/master/boot/dts/rockchip/bsp/rk3399-fine3399.dts

我上面使用的是这个，你说的是哪个？

我回头删除了这个fine3399吧，把之前的sw799改名下，你找到dts了发给我下

行

[r1172464137]

再试试

fine3399-rk3399.zip